Platelet-Rich Plasma System
D-MED
PRP Tubes
High dose and purity, engineered with Micro-Polishing Technology, a flawlessly smooth inner wall that protects the platelet fraction from the first spin to the final draw.
D-MED
Why D-MED Tubes
Excellence in every detail
Micro-Polishing Technology
D-MED PRP Tubes are manufactured with a flawlessly smooth inner wall. A polished, low-friction surface reduces platelet contact activation and aggregation during centrifugation, so more of the platelet fraction stays intact and recoverable at the plasma interface.
Gel-free, additive-controlled
No separating gel means no risk of gel carry-over into the injected dose. Sodium citrate anticoagulant is dosed precisely into every tube, protecting platelet viability from the moment of the draw through to centrifugation.
High dose, high purity
Engineered geometry and calibrated vacuum draw give a consistent plasma-to-blood ratio at every fill, translating into a reproducible, concentrated platelet dose preparation after preparation.
Trusted clinical partner
Manufactured under rigorous quality standards and strict inspection processes, D-MED PRP Tubes stand alongside physicians worldwide with global certifications and a track record across hundreds of thousands of treatments.
Inside the tube
Built for one clean separation
Every tube is sealed, vacuum-drawn and sterile-packed in pairs, ready to draw directly at the point of care, no external transfers required.
Inner wall
Micro-polished to a flawless, smooth finish that limits platelet contact activation during the spin.
Anticoagulant fill
A precise sodium citrate dose, no separating gel, nothing between the plasma and the platelet fraction.
Vacuum draw
Calibrated vacuum fills each tube to the same volume every time, for a reproducible blood-to-additive ratio.
Preparation workflow
One draw. One spin. One dose.
The smooth inner wall keeps the protocol short, a single centrifugation is enough to concentrate a clean, reproducible platelet fraction.
01
Draw
Whole blood is drawn directly into the D-MED PRP tube through calibrated vacuum fill.
02
Single spin
A single centrifugation separates the platelet-rich fraction against the polished inner wall.
03
Separate
With no gel barrier, the plasma layer is drawn off directly, free of aggregation at the interface.
04
Apply
The prepared PRP dose is ready for application through fully compatible accessories.
Measured in the lab
Measured, not marketed
Manufactured exclusively with fully integrated components. The figures below are reported from D-MED R&D Laboratories analysis.
89.1%
Platelet Recovery Rate
4.3 Billion
Platelet Dose
95.4%
Purity
D-MED R&D Laboratories Analysis Results
Clinically Proven Effectiveness Supported by 47 Scientific Publications
D-MED PRP Tubes are an advanced regenerative medicine solution whose effectiveness has been demonstrated through 47 independent scientific publications and is strongly supported by clinical literature. Scientific evidence across diverse patient populations and clinical indications confirms the product’s reliability, reproducibility, and clinical success.
D-MED PRP Tubes:
are actively utilized across 18 different medical specialties, including dermatology, orthopedics, sports medicine, physical therapy and rehabilitation, plastic surgery, dentistry, and many other clinical fields.
This multidisciplinary use, supported by scientific publications, positions our product beyond being simply a PRP solution, establishing it as an evidence-based clinical standard preferred on a global scale.
Manufacturing & quality
Controlled from raw material to dose
D-MED PRP Tubes undergo more than one hundred control and inspection stages within a single-site, fully integrated facility.
Safety control
Advanced safety control
From raw material procurement to patient delivery, D-MED PRP Tubes pass more than one hundred control and inspection stages. Every phase of production is tested, verified and documented with full transparency, open to third-party audits.
Quality system
Proven quality
Products are manufactured under GMP standards in a fully integrated facility with one ISO Class 8, four ISO Class 7 and one ISO Class 6 cleanroom. From raw-material processing and tube assembly to sterilisation and final packaging, production runs under an ISO 13485 medical-device quality management system in a single-site structure.
Research
In the light of science
D-MED continuously advances its research and development, refining Micro-Polishing Technology and tube geometry to keep raising quality standards while staying aligned with the forefront of innovation in healthcare and biomedical science.
About Us
